If your CBD packaging was designed before March 2025 and has not been reviewed since, the answer is probably no.
Every label produced after that date has to meet the requirements introduced by the streamlining amendments to the Cannabis Regulations. Product already on shelves is fine. Anything you print from here is not, unless the template has been updated.
This guide is a self-audit. Work through it against your current artwork and you will know within ten minutes whether you have a problem.
A note before starting: Health Canada does not pre-approve individual package or label designs, and compliance responsibility rests entirely with the licensed producer or processor. This article is packaging guidance from a manufacturer, not legal advice. Verify against Health Canada's Packaging and Labelling Guide, the Cannabis Regulations, and your provincial regulator before printing.
The ten-minute audit
Pull up your current label artwork and check these eight things.
- Are the actual THC and CBD quantities shown in bold? If yes, the template is out of date.
- Was the artwork last revised before March 2025?
- Does every mandatory element appear, legibly, for your specific product class?
- Is all consumer-facing copy in both English and French?
- Is the excise stamp position accounted for in the layout, per destination province?
- Does the pack meet child-resistance requirements for its product class?
- Have you confirmed the requirements of every province you sell into, not just your home province?
- Has your compliance lead signed off the current version in writing?
Anyone on that list is worth resolving before your next print run. The rest of this guide explains each one.
Start here: CBD is not a supplement in Canada
Brands arriving from the American market get this wrong more than any other single thing, and it is expensive.
In Canada, CBD is regulated under the Cannabis Act regardless of how much THC the product contains. There is no hemp-derived exemption equivalent to the US Farm Bill. A CBD product sold to Canadian consumers is a cannabis product in law. It must come from a federally licensed producer or processor, and it must carry cannabis packaging.
The practical consequence: packaging designed for the US CBD market will not comply in Canada. Not the panel layout, not the claims, not the symbols, not the colour treatment. If you are importing artwork alongside a product line, it needs rebuilding rather than adapting.
This also catches Canadian wellness and skincare brands who assume a low-THC topical sits outside the Cannabis Act. Confirm your product's classification before you commission anything.
The bold font rule that caught producers out
This is the change most likely to make your existing template non-compliant.
Licence holders were permitted to continue using labels displaying actual THC and CBD quantity in bold for one year, until 12 March 2026, so that existing label inventory could be run down. After that date, labels must meet the new requirement producers may still elect to list the actual THC and CBD quantity or concentration, provided it is not in bold font.
So the figure can stay. The emphasis cannot.
Two things follow. First, if your designer built the label with the potency figure weighted for prominence, which was the norm, because potency drives purchase, that file needs correcting. Second, authorized retailers are permitted to continue selling products with old labels indefinitely, so you will still see bold potency figures on shelves. Do not treat what is in a store as evidence that your artwork is current.
What you are now allowed to do
The same amendments that created the deadline also removed restrictions that had constrained cannabis packaging since legalisation. Most brands have not yet taken advantage of them.
The changes came in response to a long-standing industry argument: that restrictive packaging rules made it difficult for legal producers to compete with the illicit market on brand and shelf appeal.
Cut-out windows and transparent packaging. Now permitted for dried cannabis, fresh cannabis and seeds, within plain-packaging limits. For dried flowers this is a genuine differentiator; consumers are asked to see the product, and now they can.
Two-colour containers. The cap and the container of a package may be different colours. Minor on paper, meaningful on a shelf of near-identical packs.
QR codes and additional barcodes. Permitted on all cannabis product labels. This is the most valuable change available to you and the most underused.
Peel-back and accordion labels. Multi-layered and clamshell label designs are now allowed, which lets a compact package carry considerably more information.
Packaging date tolerance. The date on the label may differ from the actual packaging date by up to seven days either way. A production relief rather than a design one, but it reduces waste on pre-printed stock.
Why the QR code is the biggest win
Plain packaging limits what you can say on the pack. It does not limit what you can say on a page the pack links to.
Everything squeezed out of your panel by mandatory elements – terpene profile, full test results, harvest information, growing method, education, and brand story can live behind a code. The pack stays compliant and minimal; the depth sits one scan away, on a page you control and can update without reprinting.
Design it in rather than bolting it on. A code placed as an afterthought in a corner gets ignored. A code with a clear reason to scan printed next to it gets used.
The mandatory elements
These still have to be present, legible, and correct for your product class:
- The standardised cannabis symbol
- The health warning message
- THC and CBD content
- Net weight or volume
- Licence holder name and contact details
- Lot number
- Packaging date
- The excise stamp for the destination province
The exact requirements vary between dried flower, edibles, extracts and topicals. Check the current Packaging and Labelling Guide for your specific class rather than relying on a general list, including this one.
Child-resistance requirements also remain in force, as do container performance requirements around odour and light protection for many formats. Both affect material choice and structure, not just artwork, so they need settling before the die is cut.
Bilingual labelling is not optional
Federal requirements mandate English and French on consumer-facing packaging, and Quebec applies further requirements on top.
The design consequence is the one people underestimate: bilingual copy takes roughly twice the panel space. On a pre-roll tube or a small edibles carton, that is the difference between a workable layout and one where type has been shrunk below legibility to make it fit.
Plan for two languages in the first layout. Retrofitting French into a design built for English alone almost always produces a compromised pack, and on a small format it often forces a structural change — a larger carton, a peel-back label, or an accordion fold.
Federal rules are the floor, not the ceiling
Each province adds requirements on top of the federal baseline.
Ontario is the clearest illustration. The AGCO removed the requirement that cannabis and accessories not be visible from store exteriors in May 2025, permits locked, tamper-proof sensory display containers that let customers see and smell product without touching it, and requires retailers to display the Ontario cannabis retail seal.
Quebec applies notably stricter rules than the federal baseline, particularly around anything that could be construed as appealing to young people, and layers its own language requirements on top.
If you distribute nationally, confirm every province before finalising artwork. A pack compliant in Alberta is not automatically compliant in Quebec, and discovering that after a print run is an expensive lesson.
Design for the excise stamp
The excise stamp is a fixed element in a fixed position, applied per destination province, and it will sit on top of your artwork.
The common failure is designing the pack, approving the proof, and then finding the stamp lands across the logo or an element of the mandatory copy. Because stamps differ by province, a layout that works for one market can fail in another.
Map the stamp position for each province you ship to at layout stage. It costs nothing to plan and it is the single most common late-stage artwork problem on cannabis packaging.
What getting this wrong costs
Health Canada applies a risk-based enforcement approach and has adopted a more collaborative posture with industry, including eliminating mandatory CAPA submissions for minor inspection observations. But for major or critical violations, including packaging non-compliance, enforcement action remains firm, and recalls, licence suspensions and ministerial orders remain available.
Set against that, the direct costs are almost the smaller problem. A non-compliant run means the print cost, the die, the production time, the delay to launch, and the scramble to reprint against a retail date you have already committed to.
A compliance review before the die is cut costs a few hours. That is the whole argument.
Working within the constraints
With brand elements limited in size and number, the physical qualities of the box carry disproportionate weight. This is where cannabis packaging is won.
Finish does the work colour cannot. Matte lamination with a spot UV logo reads as considered and costs far less than it looks. Soft touch signals price point through the hand rather than the eye. Blind debossing adds a brand mark with no additional printed content at all.
Specify anti-scuff film. Cannabis packaging is handled heavily in retail, and standard matte marks visibly on the dark colours common in the category. Anti-scuff matte costs slightly more and prevents product looking shopworn.
Use structure as differentiation. Plain packaging constrains graphics, not construction. A well-engineered opening, a magnetic closure on a premium line, a distinctive carton proportion — none of these are restricted content, and all of them register.
Do not stack effects. One finish executed properly beats three competing, particularly on a pack where mandatory elements already occupy most of the surface.
Your next steps
- Pull your current label artwork and run the eight-point audit above.
- Confirm the mandatory element list for your specific product class against the current Health Canada guide.
- Confirm requirements for every province you sell into.
- Map excise stamp placement per province.
- Get written compliance sign-off before the die is cut, not after the proof.
If the audit turns up problems, treat the reprint as an opportunity rather than a cost. The 2025 amendments opened up windows, QR codes, two-colour containers and multi-layer labels. If you are reprinting anyway, you may as well come back with a better pack than the one you had.
Common questions
Does the March 2026 deadline apply to product already on shelves?
No. Authorized retailers may continue selling products carrying old labels indefinitely. The requirement applies to labels produced from that date onward.
Can I still show THC and CBD potency on the pack?
Yes. You may still list the actual quantity or concentration. You simply cannot set it in bold.
Do I need a licence to sell CBD packaging?
No packaging suppliers do not require one. The licence requirement sits with the producer or processor filling and selling the product.
Talk to us about your packaging
We manufacture cannabis and CBD packaging for the Canadian market folding cartons, rigid boxes, pre-roll packaging, mailers and labels, with matte, gloss, soft touch, spot UV and foil finishing, and window options where your product class permits them.
What we do: build the structure, die, finish and print to your specification, and flag layout problems before they reach the press excise stamp clashes, bilingual copy that will not fit the panel, artwork that will crack at the crease.
What we do not do: rule on whether your artwork is compliant. That is your compliance team's call, and any packaging supplier who tells you otherwise is selling you a risk you will carry alone.
Share your product class, dimensions, target provinces and quantity. We will come back with a quote and a 3D proof within 24 hours, with a 100-box minimum, free design support and no die or plate charges.